ประแจ/ไขควงวัดแรงแบบดิจิตอล ยี่ห้อ CEDAR
Screw tightening control
DIGITAL TORQUE DRIVER DID-4
- Unify the display section and a frame. It became stronger.
- Display Measurement Mode, Unit, Etc. on Display Section.
- Data Output is USB Form.
- Prepare each button in accordance with operation.
Button operation became simple
- The torque screwdriver is Ergonomic and light weight, yet ruggedly constructed
- Available in: lb-in, kg-cm and N-m
- Peak, Real Time and Peak Down measuring mode (selectable)
- 800 data memory.
- Programmable High and Low set points with both audible beep and Green/Red LED indicator for uniform torque tightening or GO/NO GO testing
- Programmable screw tightening counter
- Programmable Auto Zero function resets unit to zero for easy operation
- Both CW and CCW operation
- ASCII format output(USB)
- Runs on internal Ni-MH batteries (for 12 hours) Auto shut-off after 10 min. of non-use
- AC charger and carrying case included.
| Specification | DID-4 | ||
| Measuring range | 0.020 – 4 N-m | ||
| 0.20～40 kgf-cm | |||
| 0.20～35 lbf-in | |||
| Accuracy | ± 0.5% (in case of reading 499 or less = last digit +/- 3 reading) | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW (right and left) | ||
| Measuring mode | P-P Peak | Holding Peak Load Value | |
| T-R Track | Showing Real time torque value ( Used for Zero-Adjustment ) | ||
| P-D Peak down | Holding Load Value at the moment to change from upward to downword | ||
| C Real-time output | Load torque value is outputted every about 1/ 160. | ||
| Decision function | Setting of torque value | Programmable High and Low setpoints with both audible beep and Green/Red LED indicator for uniform torque tightening or GO/NO GO testing | |
The Maximum, the minimum, and the average value | Displays, memory and output the data number, the maximum, the minimum, and the average value of the measured value to 30 data. It can save by a maximum of 10 channels. | ||
| Data spec. | Data transfer | ASCII format (Baud rate : 19200) When outputting data,the cable(USB miniB) is needed. | |
| Data memory | 800 data / ten channels data | ||
| A setup of the number of counts | One to 99 count (count in a direction with a bundle) | ||
| Power supply | Ni-MH chargeable battery 1.2V×4cells 800mAh | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Charging time | From empty – less than 5hours | ||
| Continunous working time | 12 hours | ||
| Bit /Socket part | HEX6.35 | ||
| Weight | about 400g | ||
| Attachment | Bit （＋） ＃１ ＃２ | ||
| Accessories (one piece each) | AC/DC Adaptor (Charger) | ||
| An inspection report, a proofreading certificate, a traceability system figure | |||
DIGITAL TORQUE WRENCH DIW-120/75/20/15
- Unify the display section and a frame. It became stronger.
- Display Measurement Mode, Unit, Etc. on Display Section.
- Data Output is USB Form.
- Prepare each button in accordance with operation.
Button operation became simple
- The torque screwdriver is Ergonomic and light weight, yet ruggedly constructed
- Available in: lb-in, kg-cm and N-m
- Peak, Real Time and Peak Down measuring mode (selectable)
- 800 data memory.
- Programmable High and Low set points with both audible beep and Green/Red LED indicator for uniform torque tightening or GO/NO GO testing
- Programmable screw tightening counter
- Programmable Auto Zero function resets unit to zero for easy operation
- Both CW and CCW operation
- ASCII format output(USB)
- Runs on internal Ni-MH batteries (for 12 hours) Auto shut-off after 10 min. of non-use
- AC charger and carrying case included.
NEW DEVELOPMENT !! Wrench head awivels 300°
| Specification | DIW-15 | DIW-20 | DIW-75 | DIW-120 | |
| Measuring range N・m (at the time of Track) | 0.20 – 15 N･m | 0.20 – 20 N･m | 0.20 – 75 N・m | 2.0 – 120 N・m | |
| 2.0～150 kgf・cm | 2.0～200 kgf・cm | 2.0～750 kgf・cm | 20～1200 kgf・cm | ||
| 2.0～130 lbf・in | 2.0～174 lbf・in | 2.0～650 lbf・in | 20～1040 lbf・in | ||
| Accuracy | ±0.5% (F/S) (199 or less digit±1digit) | ±0.5% (F/S) (499 or less digit±3digit) | ±0.5% (F/S) (199 or less digit±1digit） | ||
| Display | The 4 figures digital display of LCD | ||||
| The measurement direction | CW-CCW (right and left) | ||||
| Measuring mode | P-P Peak | Holding Peak Load Value | |||
| T-R Track | Showing Real time torque value ( Used for Zero-Adjustment ) | ||||
| P-D Peak down | Holding Load Value at the moment to change from upward to downword | ||||
| C Real-time output | Load torque value is outputted every about1/ 160 second | ||||
| Decision function | Setting of torque value | Programmable High and Low setpoints with both audible beep and Green/ Red LED indicator for uniform torque tightening or GO/NO GO testing | |||
| The Maximum, the minimum, and the average value | Displays, memory and output the data number, the maximum, the minimum, and the average value of the measured value to 30 data. It can save by a maximum of 10 channels. | ||||
| Data spec. | Data transfer | ASCII format (Baud rate : 19200) | |||
| Data memory | 800 data / ten channels data | ||||
| A setup of the number of counts | One to 99 count (count in a direction with a bundle) | ||||
| Auto power save | 10 minutes no use, automatically switch off. | ||||
| Charging time | From empty – less than 5hours | ||||
| Continunous working time | 12 hours | ||||
| Outside size | φ34(grip)×236(L) | φ34(grip)×235(L) | φ34(grip)×320(L) | φ34(grip)×445(L) | |
| Weight (about) | 430g | 470g | 620g | 830g | |
| Socket engagement | 6.35 square, including steel ball | 9.5 square, including steel ball | 12.7 square, including steel ball | ||
| Attachment | – | One-way socket | |||
| Accessories (one piece each) | AC/DC adaptor | ||||
| An inspection report, a proofreading certificate, a traceability system figure | |||||
For more information please contact : info@kurokicorp.com