CEDAR Torque Tester/ Electric Screw Driver

เครื่องทดสอบแรงบิดไขควงไฟฟ้า ยี่ห้อ CEDAR

---

 

Torque Meter DI-9M-8/08

DI-9 series is most suitable for checking and controlling the torque of Electric Screwdriver and Torque Driver.

UPGRADE The main changed parts

1. In a display board, “measurement mode”, a “measurement unit”, “the maximum, the minimum, an average, etc.”, etc. display.
2. Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc.
3. Setup of Various Numerical Values Can be Easy and Can Carry Out Speedily.
4. Calculation of Maximum, Minimum, and Average Became Intelligible.
5. The call of the saved data became easy. The output of data also became intelligible.
6. Fault charge protection. It is pilot-lamp lighting during charge.
7. Data Output is USB Form (B Type).
8. Memory Data are 800 Affairs
9. Real-time Output is Every 1 / 180 Seconds.

The best for everyday check of an electric driver
Wide measurement range (0 – 8000digit),
it corresponds to various set torques
Can measure without inversion/
rolling-back work efficiently by OW joint (PAT.P).

 

Specification		DI-9M-8	DI-9M-08
Measuring range		0.020-8 N･m	2.0-800 mN･m
		0.20～80 kgf・cm	0.020～8 kgf・cm
		0.20～70 lbf・in	0.020～7 lbf・in
Accuracy		±0.5% (499 digit or less ±3digit)
Display		The 4 figures digital display of LCD
The measurement direction		CW-CCW (right and left)
Zero return by one touch		Return to zero by pressing clear button.
Measurement Mode		Track , P-P(peak to peak) , P-D(Peak-Down) , C(Real-time Output)
High and low limits judging function		High and low value are measurement within the limits, and can be set up.
Real-time Output		Load torque value is outputted every about1/ 180 second.
The Maximum, the minimum, and the average value display		The maximum, the minimum, average value, and the data number of 30 data are displayed.It saves to ten channels.
Data Output		ASCII format (baud rate 19200)
Auto power save		10 minutes no use, automatically switch off.
Power supply		Ni-Cd chargeable battery 1.2V × 5cells 700mAh
Charging time		About 3hours
Continuous working time		About 12hours
clearance		It is a display clearance in set-up time. (0.1 – 3.0 sec)
Socket size		□ 20mm/ □9.5mm
Dimension / Weight		W:160×D:125×H:55 / About 1kg
Recommend buffer accessories		Measuring joint OW-20/OW-60	Measuring joint OW-025/OW-10
		Cube (with a 5th page screw hole)　20x20x20 (M2.6/M3/M4/M5/M6 Tap processing)
		AC/DC adaptor
		Exclusive receipt case
		An inspection report, a proofreading certificate, a traceability system figure

* Do not use for measurement of impact tool.Do not apply more than the specified torque.

 

---

Torque Meter CD-100M/10M

UPGRADE The main changed parts

1. In a display board, “measurement mode”, a “measurement unit”, “the maximum, the minimum, an average, etc.”, etc. display.
2. Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc.
3. Setup of Various Numerical Values Can be Easy and Can Carry Out Speedily.
4. Calculation of Maximum, Minimum, and Average Became Intelligible.
5. The call of the saved data became easy. The output of data also became intelligible.
6. Fault charge protection. It is pilot-lamp lighting during charge.
7. Data Output is USB Form (B Type).
8. Memory Data are 800 Affairs
9. Real-time Output is Every 1 / 180 Seconds.

 

Specification		CD－100M		CD－10M
Measuring range (at the time of Track)		0.10～10　N・m		1.0～100　ｃN・m
		1.0～100 kgf・cm		0.10～10 kgf・cm
		1.0～90 lbf・in		0.10～9 lbf・in
Accuracy		±0.5％（F/S）(199 or less digit±1digit)
Display		The 3.5 figures digital display of LCD
The measurement direction		CW-CCW (right and left)
Measurement Mode		Track , P-P(peak to peak) , P-D(Peak-Down) , C(Real-time Output)
High and low limits judging function		High and low value are measurement within the limits, and can be set up.
Real-time Output		Load torque value is outputted every about1/ 180 second.
The Maximum, the minimum, and the average value display		The maximum, the minimum, average value, and the data number of 30 data are displayed.It saves to ten channels.
Automatic Clearance		Automatically clear the displayed value after certain time (0.5 – 3.0 sec,selectable at each 0.5 sec). Setting 0.0 sec for manual Zero clearance
One-touch zero		A clear button is pushed and it is a zero.　 Data is outputed.
Data output		ASCII format (baud rate 19200)
Power supply		Ni-Cd chargeable battery 1.2V×5cells 700mAh
Auto power save		10 minutes no use, automatically switch off.
Charging time		About 3 hours
Continunous working time		About 12 hours
Socket fit mouth		□ 20mm/ □9.5mm
Weight		Abbreviation 1 kg
Outside dimension		160（W）×125（D）×55（H）
Attachment		Measurement joint　SJ50/SJ10K		Measurement joint　SJ10
Accessories (one piece each)		AC/DC adaptor
		Exclusive receipt case
		An inspection report, a proofreading certificate, traceability system figure

 

---

For more information please contact : info@kurokicorp.com